LED TV'lerin onarım maliyeti neden bu kadar yüksek??

I ordered a TV repair service. It is so costly. Do you have similar experience? Why does it cost a lot?

It is expensive because component-level service is not done by the TV manufacturer. The costly PCB will be replaced by a service technician even if the failure may be due to a single defective component in the PCB.

It will take technical expertise and special tools to troubleshoot and replace the SMD IC’s and components. As most of the servicing is done at the field(Customer locations) it is easier for the service technician to replace the PCB with a screwdriver (and soldering iron if needed).

The consumer will spend more on this deal but with less down-time. During the era of CRT TV’s, most of the servicing was done at the component level.

Devamını oku: Devre Kartları Nasıl Onarılır?

#PCB Assembly #Consume Electronics

Resmi Oliver Smith

Oliver Smith

Oliver, PCB tasarımı konusunda yetenekli deneyimli bir elektronik mühendisidir, analog devreler, gömülü sistemler, ve prototipleme. Derin bilgisi şematik yakalamaya kadar uzanıyor, cihaz yazılımı kodlaması, simülasyon, Yerleşim, test yapmak, ve sorun giderme. Oliver, elektrik tasarımı yeteneklerini ve mekanik yeteneğini kullanarak projeleri konsept aşamasından seri üretime geçirme konusunda uzmandır.
Resmi Oliver Smith

Oliver Smith

Oliver, PCB tasarımı konusunda yetenekli deneyimli bir elektronik mühendisidir, analog devreler, gömülü sistemler, ve prototipleme. Derin bilgisi şematik yakalamaya kadar uzanıyor, cihaz yazılımı kodlaması, simülasyon, Yerleşim, test yapmak, ve sorun giderme. Oliver, elektrik tasarımı yeteneklerini ve mekanik yeteneğini kullanarak projeleri konsept aşamasından seri üretime geçirme konusunda uzmandır.

Başkaları Ne Soruyor?

Düşük adetli PCB siparişi için ne tür testler uygundur??

Küçük PCB partilerinin imalat ve montajını sipariş ettim (100adet) zaten birkaç kez. Fabrika bana PCB üzerinde test yapmak isteyip istemediğimi her sorduğunda. Ama bu konuda ne yapacağımı bilmiyorum. Ve onları kendim test ediyorum. Sonra, testin sonucu kabul edilemez 15% lehimleme sorunları. Çok fena. Sanırım tedarikçiden teslimattan önce bunları test etmesini isteyeceğim.

PCB kartlarını lehimlerken SMT pedi neden kolayca düştü??

Bir telekom şirketinde alıcıyım. Son günlerde, Bir tedarikçinin karmaşık üretimi nedeniyle önemli bir SMT PCBA siparişi ertelendi. Değiştirmeyi düşünüyorum ve PCB kartlarını lehimlerken SMT pedlerinin nasıl kolayca düştüğü konusunda çok şaşkınım. Bu tüm süreci yavaşlatır.

What will be the role of a copper layer in a metal core PCB in thermal dissipation?

In the design of a power electronic PCB, I want to use a metal PCB for heat dissipation of a TO-220 package MOSFET. To do that I want to mount metal PCB on the MOSFET with the use of thermal paste and screw exactly like we do when we use heatsink for the same package. Should I leave the copper of PCB between MOSFET surface and dielectric of PCB or remove the copper surface and leave only the dielectric opening?

Blog Makalelerinden Ayrıntılı Tavsiyeleri Okuyun

Yukarı Kaydır