Where is the ground located in a PCB?

I am learning to design a multiple layer board for a medical device, and have a question about where the ground should place.
  • On a simple PCB, it’s often done as a ground fill. The fat, thick areas are often ground.
  • On a 2-layer PCB, you may have power fills as well. You can use generalizations like this to find the ground more easily if you’re examining a PCB, but you can’t know for certain without analyzing the circuit. It’s also typical for ground to be connected at the negative end of large electrolytic capacitors. Jeszcze raz, not in every case, but it’s a place to look for it.
  • Złożony, wysoka prędkość, and high-density PCBs are multi-layer. Zazwyczaj, at least one layer will be devoted to a ground plane. This is critical for both RF and high speed digital circuits such as PCI Express, USB, SATA, DDR DRAM, Ethernet, itp. Because critical signals are routed on impedance-controlled lines referenced to a ground plane. For us, we usually run microstrip lines on the top or bottom of the PCB, so there’s a ground layer right below the top and/or bottom layer.

Czytaj więcej: Wielowarstwowa płytka drukowana

#Montaż PCB

Zdjęcie Olivera Smitha

Olivera Smitha

Oliver jest doświadczonym inżynierem elektronikiem specjalizującym się w projektowaniu płytek PCB, obwody analogowe, systemy wbudowane, i prototypowanie. Jego głęboka wiedza obejmuje ujęcie schematyczne, kodowanie oprogramowania sprzętowego, symulacja, układ, testowanie, i rozwiązywanie problemów. Oliver specjalizuje się w przeprowadzaniu projektów od koncepcji do masowej produkcji, wykorzystując swoje talenty w zakresie projektowania elektrycznego i zdolności mechaniczne.
Zdjęcie Olivera Smitha

Olivera Smitha

Oliver jest doświadczonym inżynierem elektronikiem specjalizującym się w projektowaniu płytek PCB, obwody analogowe, systemy wbudowane, i prototypowanie. Jego głęboka wiedza obejmuje ujęcie schematyczne, kodowanie oprogramowania sprzętowego, symulacja, układ, testowanie, i rozwiązywanie problemów. Oliver specjalizuje się w przeprowadzaniu projektów od koncepcji do masowej produkcji, wykorzystując swoje talenty w zakresie projektowania elektrycznego i zdolności mechaniczne.

O co pytają inni

Czy konieczna jest powłoka ochronna na zespole PCB??

Zauważyłem, że większość płytek PCB i znajdujących się na nich komponentów ma powłokę konforemną. Czy jest to niezbędny proces dla wszystkich PCB w innej dziedzinie?? Po co one są?

Jak używać dwóch anten z jednym modułem Bluetooth? (Wzmacniacz BLE)

Pracuję nad projektem wykorzystującym małą energię Bluetooth o niskim zużyciu energii (STAŁA SIĘ) sygnalizatory do śledzenia ważnych elementów. Czy istnieje sposób podłączenia dwóch anten do jednego modułu BLE, który mógłby albo nasłuchiwać/nadawać na obu antenach, albo multipleksować między nimi? Lub jakikolwiek inny pomysł?

How can I solder an SMD component with a pad on the bottom?

I am getting a PCB manufactured for a project that I am working on. One of the parts, the A4950 motor driver, has a “Podkładka” on the bottom, which is meant to be soldered to GND of the PCB for thermal dissipation. I was thinking about the prototyping, and I am unsure how I would go about (using a soldering iron), soldering the pad on the bottom.

Przeczytaj szczegółowe porady z artykułów na blogu

Przewiń na górę